Socket and switch distances from a hob | Pro Certs Software

The team at Pro Certs Software provide guidance when installing a socket or cooker switch near a hob or cooker.

There are many guides for the minimum distance a socket or cooker switch can be from a hob or cooker. The reason there are recommendations for the minimum distances is to reduce the risks associated with electrical switch gear or socket-outlets being too close to a hob or oven.

Depending on which guide you read relating to cooker connection units near hobs and ovens, the distances range from 100mm to 300mm. As the recommended minimum distance for sockets near sinks is 300mm, we’d prefer to go by the 300mm rule, based on the same factors as mentioned in the sockets and sinks guidance.

Risks

Possible risks associated with a hob or cooker switch/isolator or socket being behind a hob or cooker.

Burns

If a hob switch or isolator is located behind a hob and the user requires to turn off the hob quickly the user should NOT have to reach over a hot hob in order to turn it off.

Water and heat damage to electrical accessories

If a cooker isolator is installed behind the hob or oven there is risk of heat damage being incurred on the cooker isolator from the hob or cooker. In addition to this, should a pan boil or overheat there is the potential risk of the cooker isolator getting wet.

Limited space in a kitchen

In some scenarios there may not be enough space in the kitchen to install cooker switches, sockets or spurs 300mm away from a hob or oven. In those circumstances it would be up to the installer to decide on a safe and readily accessible alternative location. Some guidance we found recommends a minimum distance from 100mm, however 300mm is the preferred distance up to a maximum distance of 2m and certainly not directly behind the hob.

A kitchen fitter may alter the layout of an existing kitchen by relocating the hob or oven which places the hob or oven too close or directly in front of existing electrical accessories. In those circumstances you should relocate the electrical accessories to a safe location – this is best done before the new kitchen is fitted.

Sockets, switched fused spurs, light switches, cooker switches and hob isolators should not be installed behind or directly above a hob or oven.

Diagram

Electrical fittings near cookers

How far should an electrical accessory be located from a gas or electric cooker or hob? The NHBC answers this question:

‘A minimum distance of 100mm, measured horizontally from an electrical accessory to the edge of a free standing cooker or individual hob is considered acceptable for the purposes of avoiding adverse effects from using a cooker or hob. An electrical accessory should not be located immediately above a cooker or hob due to the possibility of people reaching over suffering burns or the flexible cable of connected equipment being damaged.’

Source: NHBC – Electrical Fittings Near Cookers

Part P of the Building Regulations

Design and installation; P1.

Reasonable provision shall be made in the design and installation of electrical installations in order to protect persons operating, maintaining or altering the installations from fire or injury.

BS 7671 On-Site Guide

7.4 Proximity to electrical and other services; 528.3

Electrical and all other services must be protected from any harmful mutual effects foreseen as likely under conditions of normal service. For example, cables should not be in contact with or run alongside hot pipes.

5 Isolation and switching – Means of isolation should be provided; 462.3 For every item of equipment.

5.4 Functional Switching; 463.1.3 All current-using equipment requiring control shall be controlled by a switch.

Electrician’s Guide to the Building Regulations

5.2.2 Location of accessories in kitchens;

1. Wiring accessories (e.g. sockets, switches) should be mounted on the building fabric and not kitchen furniture.

2. Cooker control switches, extractor fan switches etc. should not be mounted so that it is necessary to lean or reach over hobs for their operation.

3. Socket-outlets should be installed at a minimum of 450mm from the floor.

4. Accessories should be installed at a minimum of 300mm from the edge of kitchen sinks and draining boards.

Conclusion

The minimum distance a cooker switch, spur or socket can be from a hob or oven is 300mm horizontally away from the edge of the appliance.

Source: IET The Electrician’s Guide to the Building Regulations = 300mm

Source: NHBC Electrical Fittings Near Cookers = 100mm

Software and solutions

Pro Certs Software designs, develops and publishes electrical Apps and mobile electrical software to serve the electrical industry. The Apps are designed from the ground up with the user in mind for ease of use, reliability and availability. Furthermore, all electrical Apps are designed to work offline, even in ‘airplane’ mode.

Apps are available on Android and iOS platforms, while the Pro Certs electrical certification software is also available on Windows 10.

Download the Pro Certs Software Electrical Tools and Reference App by clicking here

Comments are closed.